OPT300 - Cisco Optical Technology Advanced
OPT300 - Cisco Optical Technology Advanced Course Details:
This course covers topics not covered in the intermediate version. You will learn how to design DWDM networks using the Cisco Transport Planning (CTP) tool. You learn how the 40- and 80-channel mesh networks are designed, and you set up a six-node WXC-based 40- or 80-channel mesh network. You will also learn how the 40-channel SMR1 and/or SMR2 network is designed and set up a six-node 40-channel network. In the hands-on labs, you learn to configure: the Cisco Transport Controller, the 10 Gbps (G) data cards, the 1 gigabit/10 gigabit Ethernet enhanced crossponder, any rate muxponder and crossponder, 100G transponders and muxponders, 10G encryption, and T1 over Ethernet. There is also a review of G.709 encapsulation, G.7041 Generic Framing Protocol (GFP), forward error correction and coherent transmission. Additionally, you will learn how to add a node to the existing six-node ring and troubleshoot the configuration. The course combines lecture materials and hands-on labs throughout to make sure that you are able to successfully deploy a Cisco data over DWDM network.
Call (919) 283-1674 to get a class scheduled online or in your area!
1. Cisco Transport Planner (CTP) Design Tool
2. Cisco Transport Controller (CTC) Operations
3. WSS- and WXC-Based Mesh Networks
4. Node Turn-Up: 40/80 WXC Mesh Technology
5. Install Circuits and View Power Levels in WSS and WXC Networks
6. SMR-Based Network and Node Turn-Up
7. Install Circuits and View Power Levels in SMR1 and 2 Networks
8. G.709 Encapsulation and 10G Transponders and Encapsulation Options
9. 10 Gigabit Transponders
10. Generic Framing Protocol G.7041 and 10G Data Multiplexer Enhanced Cards and Encapsulation Options
11. Any-Rate Muxponder and Crossponder Cards
12. Ethernet and VLANs
13. 10 GE-XP and GE-XP Enhanced Cards, Settings, and Circuits Layer 1
14. Quality of Service
15. Layer 2 XP-E Cards Protected Ring, CoS Marking by Port, Customer VLAN, and QoS
16. T1 over Ethernet in Crossponder Network
17. 100G Transponder and Muxponder Installation and Circuits
18. 10G Encryption Card
19. Add-a-Node Design and Installation
20. ONS 15454 MSTP Troubleshooting
*Please Note: Course Outline is subject to change without notice. Exact course outline will be provided at time of registration.
- Run the Cisco CTP tool and design sample DWDM networks
- Principles of a wavelength cross-connect (WXC)-based mesh network
- Configure a six-node WXC-based mesh network and create DWDM circuits
- Principles of a single-module ROADM (SMR) based mesh network
- Configure a six-node SMR-based mesh network and create DWDM circuits
- Configure the 10-GB data cards with appropriate G.709 options and create data circuits
- Install and configure the any rate crossponder card for 8 x 20 protected data mode
- Properly configure Ethernet options for Layer 1 transport using the Gigabit Ethernet and 10 Gigabit Ethernet crossponder cards
- Install Ethernet options for Layer 2 protected and unprotected data ring circuits using the Gigabit Ethernet and 10 Gigabit Ethernet crossponder cards
- Provision incoming class of service (CoS) marking by port and by customer VLAN and incoming traffic shaping
- Understand -general queuing theory and set up quality of service (QoS) as implemented in the Gigabit Ethernet and 10 Gigabit Ethernet enhanced crossponder cards
- Install and connect circuits to carry T1 over Ethernet
- Install and configure 100 Gigabit Ethernet transponder and muxponder cards and circuits
- Install the 10G Encryption Card and verify error-free operation
- Add a node to the existing six node 40-channel ring
- Troubleshooting techniques and lab
- Technical professionals who need to know how to deploy data over the DWDM network.
- Designers
- System engineers and implementation staff
- Network operations center personnel
- Technical support personnel who are involved with the deployment, operations, and maintenance of the Cisco ONS 15454 MSTP system
- Channel partners and resellers